How To Convert Pps 43 To Sbr

Looking for infoprocedure on how to convert a PPs-43 semi-auto pistol with the welded stock into an SBR. So its possible and as u can see.

Pps 43c Sbr Conversion Guns

But ive been seeing 9mm conversion barrels and things for it.

How to convert pps 43 to sbr. After that you can put any barrel in it you want but it will still be a SBR. Once that is separated you can remove the push pin. The semi conversions for the PPs and KP usually involve a hammer fire mechanism one from a Remington semi auto shotgun or rifle fits as a drop in to the lower frame assembly with a bit of metal surgery.

I have a 9mm pistol and then fixing to aquire 2 more 9mm firearms. The PPS-43 Pistolet-Pulemet Sudaeva model of 1943 Sudaev submachine gun was born as an answer to the need for weapon that would be more compact and mobile than the PPSh-41 then in use by the Soviet Army. Sometime b4 Christmas i am planning on ordering a pps43c.

Itll be an easy swap though just flip a lever to take the barrel and shroud off and replace with a proper barrel and shroud from a parts kit. I press out the 762 barrel and put in a KP Products 9mm barrel. It takes about 15-20 minutes to make the stock functional if you do the form 1.

Ive looked at the way the stock is pinned and can think of multiple ways to do it be I want to do it the best agreed upon way. Now the 43 is chambered for 762x25. Converting the PPS-43C to an SBR with a fully operational folding stock is quite simple and can be accomplished with common hand tools.

Once you remove the fake button and locking bar you should be able to rotate the stock around freely. At one time C-S Metall Werkes was offering an SBR conversion package on the PPS-43C pistols for like 150 which included re-activating the stock apparently there are some parts left out that needed to be fabricated in addition to breaking the welds and engraving the receiver. The bolt needs to be drilled to remove the fixed firing pin and replace it with a spring loaded one that is struck by the hammer.

So it would just make sense to convert the 43 to 9mm. Those PPS43c stocks are not welded closed. Aiming the PPS-43C without the benefit of the folding stock is a little bit awkward but shooting from the hip is fun and easy.

The conversion from pistol to rifle was very simple. The PPSh-41 was somewhat too long to be used by tank crews and mobile recon groups and paratroopers so late in 1941 the Red. A parts kit from someone like Sportsmans Guide is required to provide some of the parts needed to complete the folding stock mechanism - and it provides an extra magazine and a few other goodies.

PPS-43 As of 01-27-17 we currently have about 3 of these we can complete in about 2 weeks of receiving an order 69500 2000 SH We can also build an SBR with folding stock for an additional 10000. My next SBR will be my Suomi. You can have all the barrels you want and cut them to SBR length.

The button has to be ground out and removed from the inside. There are gunsmiths who can reactivate the folding stock if you complete the proper BATF paperwork and pay the fee which will turn your PPS-43C into a registered short barreled rifle SBR. Almost every underfolder-style stock is wobbly and the PPS-43Cs over folder was no exception.

Im interested in doing this conversion but Im not going to be able to figure it out on my own. The hole in the top of the receiver is made smaller so the pin cant be pushed down. The perceived recoil from the PPS is less than any of the Glock SBR enclosures Ive tested which also have pretty low recoil impulse.

In order to fold the stock down you have to remove the pin from the latch block by grinding the weld off. You must be new to the gun community otherwise you would know you can no longer register or make a machine-gun not since 1986 so youre a little late to do that. I know how that goes.

At 6 pounds 13 ounces the PPS-43C ate up all of the recoil from the 762x25mm round. Ive been thinking about buying one of these pistols to do the conversion but not if I cant figure out how to SBR it. Figure out what you want to do.

If you want to put a stock on it and keep your current barrel that means you need to pay the tax and build a SBR. Ash wJMac Customs shooting the PPS 43C SBRThanks for watchingPlease. Im going to short barrel rifle LEGALLY a recently purchased PPS43-C from Royal Tiger Interordinance.

Then you will need to install the button and locking bar assembly from the parts kit stock assembly. The PPS-43c stock is disabled by a non-functinal buttonlocking bar assembly. Google has failed me.

A handgun was not fun nor was buying the 762x25 ammo. A 9mm SBR Is the way to go. And ppl who have converted them to 9mm.

Pps 43 Semi Auto Military Surplus Collectors Full30

Share this post